mems oscillator, ultra performance, high freq., lvcmos/ hcmos compatible, 80.0 mhz to 220.0mhz IM811 series ilsi america phone 775-851-8880 fax 775-851-8882 email: e-mail@ilsiamerica.com www.ilsiamerica.com specifications subject to change without notice rev: 01/30/16_a page 1 of 7 features: ? mems technology ? direct pin to pin drop-in replacement for industry-standard packages ? ultra-low phase jitter: 0.5 psec (12 khz to 20 mhz) ? lvcmos/hcmos compatible output ? industry-standard package 2.5 x 2.0, 3.2 x 2.5, and 5.0 x 3.2 mm x mm ? pb-free, rohs and reach compliant ? fast delivery times typical applications: ? fibre channel ? server and storage ? gpon, epon ? electrical specifications: frequency range 80.000 mhz to 220.000mhz frequency stability see part number guide inclusive of initial to lerance, operating temperature range, load, and voltage operating temperature see part number guide supply voltage (vdd) 10% see part number guide current consumption 34 ma typ./ 36 ma max 30 ma typ./ 33 ma max no load condition, f = 100 mhz, vdd = +2.5 v, +2.8 v or +3.3 v no load condition, f = 100 mhz, vdd = +1.8v oe disable current 31 ma max 30 ma max vdd = +2.5 v, +2.8 v or +3.3 v, oe = gnd vdd = +1.8 v, oe = gnd standby current 70 a max 10 a max vdd = +2.5 v, +2.8 v or +3.3 v, st = gnd vdd = +1.8 v, st = gnd waveform output lvcmos/hcmos symmetry 45%/55% 40%/60% f = less than 165 mhz all vdds f = greater than 165 mhz all vdds rise / fall time 1.2 nsec typ./ 2.0 nsec max 15 pf load, 10% to 90% of vdd logic ?1? 90% of vdd min logic ?0? 10% of vdd max input voltage high 70% of vdd min pin 1, oe or st input voltage low 30% of vdd max pin 1, oe or st input pull-up impedance 100 k ? typ./ 250 k ? max 2.0 m ? min pin 1, oe logic high or logic low, or st logic high pin 1, st logic low startup time 7 msec typ./ 10 msec max measured from the time vdd reaches its rated minimum values oe enable/disable time 115 nsec max f= 80 mhz, for other fr equencies, t_oe = 100 nsec = 3 cycles resume time 10 msec max in standby mode, measured from the time st pin crosses 50% threshold. rms period jitter 1.5 psec typ./ 2.0 psec max 2.0 psec typ./ 3.0 psec max f = 156.25 mhz, vdd = +2.5 v,+2.8 v or +3.3 v f = 156.25 mhz, vdd = +1.8 v rms phase jitter (random) 0.5 psec typ./ 1.0 psec max f = 156.25 mhz, integration bandwidth = 12 khz to 20 mhz first year aging 1.5 ppm at +25oc 2oc 10-years aging 5.0 ppm at +25oc 2oc notes: ? all min and max limits are specified over temperature and rate d operating voltage with 15pf output unless otherwise stated. ? typical values are at +25oc and nominal supply voltage. a bsolute maximum limits storage temperature -65oc to +150oc supply voltage (vdd) -0.5 vdc to 4.0 vdc electrostatic discharge 2000 v max solder temperature (follow standard pb free soldering guidelines) 260oc max junction temperature 150oc max
mems oscillator, ultra performance, high freq., lvcmos/ hcmos compatible, 80.0 mhz to 220.0mhz IM811 series ilsi america phone 775-851-8880 fax 775-851-8882 email: e-mail@ilsiamerica.com www.ilsiamerica.com specifications subject to change without notice rev: 01/30/16_a page 2 of 7 ordering information: part number guide packages input voltage operating temperature output drive strength stability (ppm) select function frequency IM811b ? 5.0 x 3.2 IM811c ? 3.2 x 2.5 IM811d ? 2.5 x 2.0 1 = +1.8 v 6 = +2.5 v 2 = +2.7 v 7 = +3.0 v 3 = +3.3 v 1 = 0oc to +70oc 2 = -40oc to +85oc 3 = -20oc to +70oc - = default e = 10 f = 20 a = 25 b = 50 h = tri-state s = standby - frequency sample part number: IM811c-31-fs-100.0000mhz this 100.0000 mhz oscillator in a 3.2 x 2.5 package with stability 20 ppm from 0oc to +70oc using a supply voltage of +3.3 v. with pin 1 function as standby. output drive strength is only set to the default level. sample part number: IM811d-13-ah-125.0000mhz this 125.0000 mhz oscillator in a 2.5 x 2.0 package with stability 2 5 ppm from -20oc to +70oc using a supply voltage of +1.8 v . with pin 1 function as tri-state. output drive strength is only set to the default level. notes: ? not all options are available at all frequencies and temperatures ranges. ? please consult with sales department for any other parameters or options. ? oscillator specification subj ect to change without notice. phase noise: figure 1: phase noise, 156.25 mhz, +3.3 v lvcmos output
mems oscillator, ultra performance, high freq., lvcmos/ hcmos compatible, 80.0 mhz to 220.0mhz IM811 series ilsi america phone 775-851-8880 fax 775-851-8882 email: e-mail@ilsiamerica.com www.ilsiamerica.com specifications subject to change without notice rev: 01/30/16_a page 3 of 7 performance plots figure 2: idd vs frequency figure 3: rms period vs frequency figure 4: duty cycle vs frequency figure 5: rms phase jitter vs frequency figure 6: idd vs temperature, 100 mhz output figure 7: rise time vs temperature, 100 mhz output note: all plots are measured with 15pf load at room temperature, unless otherwise stated.
mems oscillator, ultra performance, high freq., lvcmos/ hcmos compatible, 80.0 mhz to 220.0mhz IM811 series ilsi america phone 775-851-8880 fax 775-851-8882 email: e-mail@ilsiamerica.com www.ilsiamerica.com specifications subject to change without notice rev: 01/30/16_a page 4 of 7 test circuit waveform environmental specifications: environmental compliance parameter condition/test method mechanical shock mil-std-883f, method 2002 mechanical vibration mil-std-883f, method 2007 temperature cycle jesd22, method a104 solderability mil-std-883f, method 2003 moisture sensitivity level msl level 1 at +260oc pb free solder reflow profile ts max to t l (ramp-up rate) 3oc / second max preheat temperature min (ts min) temperature typ (ts typ) temperature max (ts max) time (ts) 150oc 175oc 200oc 60 to180 seconds ramp-up tate (t l to tp 3oc / second max time maintained above temperature (t l ) time (t l ) 217oc 60 to 150 seconds peak temperature (tp) 260oc max for seconds time within 5oc to peak temperature (tp) 20 to 40 seconds ramp-down rate 6oc / second max tune 25oc to peak temperature 8 minute max moisture sensitivity level (msl) level 1 units are backward compatible with +240oc reflow processes
mems oscillator, ultra performance, high freq., lvcmos/ hcmos compatible, 80.0 mhz to 220.0mhz IM811 series ilsi america phone 775-851-8880 fax 775-851-8882 email: e-mail@ilsiamerica.com www.ilsiamerica.com specifications subject to change without notice rev: 01/30/16_a page 5 of 7 pin functionally pin description pin symbol functionality pin assignments 1 oe tri-state high or open = specified frequency output low = output is high impedance, only output is disabled. 14 3 2 top view gnd vdd out oe st st standby high or open = specified frequency output. low = output is low. device goes to sleep mode. supply current reduces to standby current. 2 gnd power electrical ground 3 out output oscillator output 4 vdd power power supply voltage notes: 1. in oe or st mode, a pull-up resistor of 10.0 k ? or less is recommended if pin 1 is not externally driven 2. a capacitor of value 0.1 f or higher bet ween pin 4 (vdd) and pin 1 (gnd) is required. timing diagrams: figure 8: startup timing (oe/ mode) figure 9: standby resume timing ( mode only) figure 10: oe enable timing (oe mode only) figure 11: oe disable timing (oe mode only)
mems oscillator, ultra performance, high freq., lvcmos/ hcmos compatible, 80.0 mhz to 220.0mhz IM811 series ilsi america phone 775-851-8880 fax 775-851-8882 email: e-mail@ilsiamerica.com www.ilsiamerica.com specifications subject to change without notice rev: 01/30/16_a page 6 of 7 mechanical details: package dimensions and suggest land pattern marking 5.00 0.05 3.20 0.05 0.80 2.39 1.15 1.1 0.80 max 2.54 2.20 1.5 1.6 opton b: 5.00 x 3.20 package 3 4 2 1 bottom view 3 marking 3.20 0.05 2.500.05 0.90 2.1 0.9 0.7 0.80 max bottom view 2.20 1.90 1.4 1.2 option c: 3.20 x 2.50 package 4 2 1 marking 2.50 0.05 2.40 0.05 1.10 1.00 0.75 0.5 0.80 max bottom view 1.90 1.50 1.1 1.0 option d: 2.70 x 2.40 package (100% compatible with 2.50 x 2.00) 21 3 4 suggested land pattern suggested land pattern suggested land pattern marking line 1 = xxxxx (lot code) dot to denote pin 1 location package information leadframe: c194 plating: nipdau
mems oscillator, ultra performance, high freq., lvcmos/ hcmos compatible, 80.0 mhz to 220.0mhz IM811 series ilsi america phone 775-851-8880 fax 775-851-8882 email: e-mail@ilsiamerica.com www.ilsiamerica.com specifications subject to change without notice rev: 01/30/16_a page 7 of 7 tape and reel dimensions direction of feed ref: eia-481-e q3 q4 q2 q1 width tape pitch reel dia part number size pitch tape width pin orient. reel dia. count IM811b 5.0 x 3.2 8.0 0.1 12.3 max q1 180 1000 330 3000 IM811c 3.2 x 2.5 4.0 0.1 8.3 max q1 180 3000 IM811d 2.5 x 2.0 4.0 0.1 8.3 max q1 180 3000 notes: ? all dimensions are in mm. ? do not scale drawings. proprietary and confidential this document contains proprietary information, and s uch information may not be disclosed to others for any purpose nor used for manufacturing purposes wi thout written permission from ilsi america.
|
